How to Set up a Bath Tub Yourself
How to Set up a Bath Tub Yourself
Blog Article
The article author is making a number of great annotation related to Tools You Need to Install a New Bathtub as a whole in this article below.
Mounting a bathtub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging task. If the old tub is conveniently easily accessible, the task can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and place the new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub as well as embeded in the new one. See to it you have qualified on your own for the job as well as fit attempting it. Instead of employing a contractor to take over a halfway-completed project, it is far better to take into consideration employing one prior to you begin. Possibilities are you might require an expert plumber to make tube links.
This post will certainly assist you set up a brand-new bathtub in your bathroom if you have currently purchased a brand-new bathtub and also do not require to alter the arrangement of your previous water system pipes.
Your devices as well as material list ought to consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of removing the existing faucets can be rather troublesome due to the restricted gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers remain in area between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type should be connected to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water and also check all joints and also brand-new pipework for leakages and also tighten them if needed. Fill the tub as well as also examine the overflow outlet and the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait until the tub has been utilized at least when as this will settle it right into its final placement.
Planning for the Installation
First of all, the supporting frame provided with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid pressure on the tub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split an inflexible seal, triggering the water to permeate the wall surface between the bathroom and the tiling, causing difficulties with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a short review down below. We'd be interested to see your feelings about this post. We are looking forward that you visit us again soon. If you appreciated our blog posting kindly remember to pass it around. We treasure reading our article about How to Install a Bathtub Yourself.
Suggested Site
Report this page